imgboxbg

NEWS  CENTER

昌弘矿山机械

Why is there no crushing hoist? Sorting out common problems of no crushing hoist

  • Categories:Industry trends
  • Author:
  • Origin:
  • Time of issue:2020-10-04
  • Views:0

(Summary description)1. Why is there no bucket elevator without crushing?
Belt conveyors are usually used for drive selection. Because the manufacturer chose a continuous bucket type non-crush elevator. However, we know that belt conveyors are relatively poor in lifting products. Before the product starts to roll the belt down, it can only be tilted 15 or 16 degrees. Therefore, when manufacturers need to upgrade their products, they need to use long conveyor belts that take up a lot of floor space (not economically fast), or install some type of lifting equipment, such as a non-crushing elevator.

Why is there no crushing hoist? Sorting out common problems of no crushing hoist

(Summary description)1. Why is there no bucket elevator without crushing?
Belt conveyors are usually used for drive selection. Because the manufacturer chose a continuous bucket type non-crush elevator. However, we know that belt conveyors are relatively poor in lifting products. Before the product starts to roll the belt down, it can only be tilted 15 or 16 degrees. Therefore, when manufacturers need to upgrade their products, they need to use long conveyor belts that take up a lot of floor space (not economically fast), or install some type of lifting equipment, such as a non-crushing elevator.

  • Categories:Industry trends
  • Author:
  • Origin:
  • Time of issue:2020-10-04
  • Views:0
Information

        1. Why is there no bucket elevator without crushing?

  Belt conveyors are usually used for drive selection. Because the manufacturer chose a continuous bucket type non-crush elevator. However, we know that belt conveyors are relatively poor in lifting products. Before the product starts to roll the belt down, it can only be tilted 15 or 16 degrees. Therefore, when manufacturers need to upgrade their products, they need to use long conveyor belts that take up a lot of floor space (not economically fast), or install some type of lifting equipment, such as a non-crushing elevator.

    There are two types of bucket crusherless elevators: centrifugal and continuous. The centrifugal type is usually used to transport grains and other fragile materials weighing no more than 50 pounds per square foot. In this elevator, the shovel will dig out a pile of grain and throw the grain on top of the elevator.

  When the material is not digging continuously, the material is conveyed to the bucket elevator, and under the action of gravity, it usually enters the shovel connected with the belt. The bucket lifts the product and uses gravity to discharge the product to the bottom of the elevator.

   2、The problems of bucket-type non-crushing hoist

      (1)、Maintain

  As mentioned above, although there are many problems with bucket-type crushless elevators. In short, they can be maintenance nightmares. They are complex, use motors that require maintenance, and increase energy costs. The number of gears and parts to be tracked and replaced has been increased.

    Manufacturers using bucket-type crush-free elevators rely on plastic buckets bolted to rubber bands. When the machine collects and lifts materials, these bolts bear a lot of force. If these bolts begin to fail and cannot be maintained in time, the shovel will tear the belt, causing a lot of damage and causing a lot of downtime.

     (2)Confusion

  Another minor issue is belt tracking. If the belt deviates slightly from the track, the belt and shovel may begin to wear. As the belt wears, it loses its integrity. The shovels are worn out, and they cannot hold the material. This will cause unnecessary materials to fall on the bottom of the elevator that does not break during the two meals, and the manufacturer must discard the shovel or manually return it to the system.

      (3)、Material

  Paper jam is one of the common problems of bucket-type crushless elevators. Mobile products can be locked to each other or stuck in the frame of the device. Then, before continuing production, the production line must be closed, the elevator opened, and the jammed material must be removed. Paper jams can also occur when materials are accumulated on the shell or chassis of bucket elevators and when the machine is cut.

 

Keyword:

Scan the QR code to read on your phone

HOT LINE: 

Contact: Manager Pang
Phone:
+86-13932836877, +86-15832856785,

+86-13315840327
Tel: +86-318-4869777
Fax: +86-318-4868277
E-mail: 384023722@qq.com
Add: West Of Nanxiao Road, Matou Town,

Hengshui City, Hebei Province, China

MOBILE SITE

Copyright © 2020 Hengshui Chang Hong Mining Machinery Co., Ltd.  All Right Reserved  冀ICP备13014199号-1